2013年4月20日 星期六

最近把老電腦的硬碟换成CF卡

想說用硬碟太吵,光碟開機太慢(Linux可用光碟跑)
就買了CF轉IDE介面卡
說句實話,挺快的
放上hdparm跑的數據
/dev/sda: Timing cached reads: 288 MB in 2.00 seconds = 143.79 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.23 MB/sec 使用的硬體 processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 11 model name : Intel(R) Celeron(TM) CPU 1000MHz 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:07.2 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) 00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) 00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50) 00:09.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 43) 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) 01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) ata1.00: CFA: CF CARD, 20100329, max UDMA/133 ata1.00: 31293360 sectors, multi 0: LBA ata1.00: limited to UDMA/33 due to 40-wire cable ata1.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA CF CARD 2010 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 31293360 512-byte logical blocks: (16.0 GB/14.9 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
其實跑有關資料的話挺快的,雖然沒真的固態硬碟快
對於老舊的電腦來說確實提高効能了

2013年2月27日 星期三

關於多顯示畫面的xorg.conf設定

主要設定區ServerLayout
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0 #主畫面位置
Screen 1 "Screen1" LeftOf "Screen0" #第二畫面位置
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
Option "Xinerama" "on" # Xinerama功能
EndSection

2013年1月26日 星期六

换了ATI的顯卡,重新設定Xwindow

因為换了ATI顯卡所以把kernel重編譯並且修改了xorg.conf
Section "Device"
Identifier "Card0"
Driver "radeon" # 主要把Driver改ㄧ下就可以了
#Option "monitor-VGA" "Monitor0"
BusID "PCI:1:0:0"
EndSection
不過如果裝ATI的驅動程式開雙顯卡會產生x window的錯誤
所以咧,我就没裝